 | |  | | | Telephone Bracket
|  | |
Description: Fit a new galvanised telephone bracket to your new fascias dont run the risk of having an old bracket leaving rusty stains
|
| |  | |  |
|
| | | | | Comb Filler (1mt)
|  | |
Description: Fix to top of fascia if your roof has pantiles. This will stop birds entering the roof space
|
| | | | |
|
| | | | | Over Fascia Protector (.9 Mt)
|  | |
Description: This is the modern way to replace decayed sarking felt. Remove the 1st course of tiles and nail this product onto your rafters and allow the flexible front edge to drape into your gutter. Re-fix tiles and alas your fascia is now protected from unsightly water stains.
|
| | | | |
|
| | | | | Roll on Fascia Protector
|  | |
Description: 20 metre x 225mm DPC membrane. This product can be tucked up and under the lower course of tiles to provide facia protection without the need to remove the lower course of tiles. Cheaper and quicker to fit than the 'Over Fascia Protector'
|
| | | | |
|
| | | | | Over Fascia Ventilator (1mt)
|  | |
Description: Used as an alternative to soffit vents where consumer does not want to see ventilation slots
|
| | | | |
|
| | | | | Over Fascia Vent, Protection & Comb
|  | |
Description: 3 in 1 profile in a 900mm length
Comb filler
Ventilator (built in underneath)
Over Fascia Protector
|
| | | | |
|
| | | | | Hunter Gutter Guard (black)
|  | |
Description: 5 metre pack which is only suitable for half round and squareline gutters. This gutter guard clips together and will lay flat inside the gutter
|
| | | | |
|
| | | | | Aluminium Gutter Guard
|  | |
Description: 7.5 metre roll. Can be bent and moulded to fit into most gutters. 150mm width
|
| | | | |
|
| | | | | Hedgehog Gutter Filter
|  | |
Description: 4 metre length.
See the video Click Here
|
| | | | |
|
| | | | | Drainpipe Filter
|  | |
Description: With this product you can forget about fitting leafguards, simply allow the leaves to be washed down the pipe and into this filter which is easily emptied at whatever position you decide to fix it at. Available in black and white (we will call you to discuss the colour required upon receipt of order)
Will fit 68mm round & 65mm square pipe
|
| | | | |
|
| | | | | Drainsmart (Gulley Cover)
|  | |
Description: This simple bit of kit will stop leaves blocking up your drains. Comes in either black or white and fits both round and square pipe up to 68mm. You can state which colour you require in the 'special instruction' box presented during the checkout process
Check out our manufacturers website drainsmart
|
| | | | |
|
| | | | | 150mm Galvanised Snowguard
|  | |
Description: 2 metre lengths of galvanised snowguard. You will need 2 brackets for the first length and then one bracket for subsequent lengths(see below)
See the video Click Here
|
| | | | |
|
| | | | | Galvanised Snowguard Bracket
|  | |
Description: the snowguard shoud be fixed to the upright bracket with wire (not included)
|
| | | | |
|
| | | | | Rainsava
|  | |
Description: For directing rainwater into a water butt
|
| | | | |
|
| | | | | Vent Trim (refurb)
|  | |
Description: 5 metre length of continuous soffit vent with 9mm channelled groove for refurbishment
|
| | | | |
|
| | | | | Vent Trim (new build)
|  | |
Description: 5 metre length of continuous soffit vent with 9mm channelled groove for new build
|
| | | | |
|
| | | | | Flyscreen Mesh
|  | |
Description: 15 metre roll x 75mm wide. This handy flyscreen tape will prevent insects entering the loft space through the grooves in pre-ventilated soffit board. Simply peel off tape and stick to back of soffit.
|
| | | | |
|
| | | | | GRP Roof Spire
|  | |
Description: This roof spire is flat backed and manufactured in GRP. The spire measures 910mm and should be fixed using clear silicone and screws
|
| | | | |
|
| | | | | Convex Decorative Fascia
|  | |
Description: This beautifully crafted 16mm board is 5 metres long and can be fitted directly onto rafter timbers without the need for backing board. Min profile depth is 160mm, max profile depth 220mm.
|
| | | | |
|
| | | | | Concave Decorative Fascia
|  | |
Description: This beautifully crafted 16mm board is 5 metres long and can be fitted directly onto rafter timbers without the need for backing board. Min profile depth is 160mm, max profile depth 220mm.
|
| | | | |
|
| | | | | Bargeboard Finial (black)
|  | |
Description: For those finishing touches to the apex. 340mm long
|
| | | | |
|
| | | | | Bargeboard Finial (white)
|  | |
Description: For those finishing touches to the apex. 340mm long
|
| | | | |
|
| | | | | Bargeboard Finial (golden Oak)
|  | |
Description: For those finishing touches to the apex. 340mm long
|
| | | | |
|
| | | | | Bargeboard Finial (mahogany)
|  | |
Description: For those finishing touches to the apex. 340mm long
|
| | | | |
|
| | | | | 70mm Soffit Vent (white)
|  | |
Description: Push & fit vent, may need a quick squirt of silicone to hold in place. You will need a 70mm holesaw for cutting the hole in the board. Should be on this page, failing which, go to the tools section
|
| | | | |
|
| | | | | 70mm Soffit Vent (black)
|  | |
Description: Push & fit vent, may need a quick squirt of silicone to hold in place. You will need a 70mm holesaw for cutting the hole in the board. Should be on this page, failing which go to the tools section
|
| | | | |
|
| | | | | 70mm Soffit Vent (brown)
|  | |
Description: Push & fit vent, may need a quick squirt of silicone to hold in place. You will need a 70mm holesaw for cutting the hole in the board. Should be on this page, failing which go to the tools section
|
| | | | |
|
| | | | | 70mm Soffit Vent (light oak)
|  | |
Description: Push & fit vent, may need a quick squirt of silicone to hold in place. You will need a 70mm holesaw for cutting the hole in the board. Should be on this page, failing which go to the tools section
|
| | | | |
|
